Simulation Analysis on the Potential Application of Matched Bandstop to Bandpass Filter in Filter Integrated SPDT Switch Design

Authors

  • A. M. Zobilah Microwave Research Group (MRG), Centre for Telecommunication Research & Innovation (CeTRI), Faculty of Electronic and Computer Engineering (FKEKK), Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia.
  • N. A. Shairi Microwave Research Group (MRG), Centre for Telecommunication Research & Innovation (CeTRI), Faculty of Electronic and Computer Engineering (FKEKK), Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia.
  • Z. Zakaria Microwave Research Group (MRG), Centre for Telecommunication Research & Innovation (CeTRI), Faculty of Electronic and Computer Engineering (FKEKK), Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia.
  • B. H. Ahmad Microwave Research Group (MRG), Centre for Telecommunication Research & Innovation (CeTRI), Faculty of Electronic and Computer Engineering (FKEKK), Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia.
  • M. K. Zahari Microwave Research Group (MRG), Centre for Telecommunication Research & Innovation (CeTRI), Faculty of Electronic and Computer Engineering (FKEKK), Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia.
  • P. W. Wong Electrical & Electronic Engineering Department, Universiti Teknologi Petronas (UTP), Bandar Seri Iskandar, 31750 Tronoh, Perak, Malaysia.

Keywords:

Filter Integrated Switch, Single Pole Double Throw, Bandstop to Bandpass, Switchable Filter

Abstract

This paper presents the simulation analysis on the potential application of matched bandstop to bandpass filter in filter integrated switch (FIS) design. The FIS consists of matched band-stop to bandpass filter integrated with single-pole-double-throw (SPDT) switch. The proposed design was demonstrated for 2.45 GHz applications in wireless data communication systems such as Bluetooth and Zigbee. The filter was based on L-shape lossy resonator, which can provide an absorptive feature. PIN diodes were used as switching elements for the SPDT switch and to reconfigure between band-stop and bandpass responses. Therefore, the key advantages of the proposed design are high isolation and good return loss at both ON- and OFF-state ports. As a result, the simulation showed the followings: higher than 10 dB of return loss and greater than 25 dB of isolation at the operation frequency.

Downloads

How to Cite

Zobilah, A. M., Shairi, N. A., Zakaria, Z., Ahmad, B. H., Zahari, M. K., & Wong, P. W. (2018). Simulation Analysis on the Potential Application of Matched Bandstop to Bandpass Filter in Filter Integrated SPDT Switch Design. Journal of Telecommunication, Electronic and Computer Engineering (JTEC), 10(4), 127–131. Retrieved from https://jtec.utem.edu.my/jtec/article/view/4820

Issue

Vol. 10 No. 4: October - December 2018

Section

Articles

License

TRANSFER OF COPYRIGHT AGREEMENT

The manuscript is herewith submitted for publication in the Journal of Telecommunication, Electronic and Computer Engineering (JTEC). It has not been published before, and it is not under consideration for publication in any other journals. It contains no material that is scandalous, obscene, libelous or otherwise contrary to law. When the manuscript is accepted for publication, I, as the author, hereby agree to transfer to JTEC, all rights including those pertaining to electronic forms and transmissions, under existing copyright laws, except for the following, which the author(s) specifically retain(s):

  1. All proprietary right other than copyright, such as patent rights
  2. The right to make further copies of all or part of the published article for my use in classroom teaching
  3. The right to reuse all or part of this manuscript in a compilation of my own works or in a textbook of which I am the author; and
  4. The right to make copies of the published work for internal distribution within the institution that employs me

I agree that copies made under these circumstances will continue to carry the copyright notice that appears in the original published work. I agree to inform my co-authors, if any, of the above terms. I certify that I have obtained written permission for the use of text, tables, and/or illustrations from any copyrighted source(s), and I agree to supply such written permission(s) to JTEC upon request.


Most read articles by the same author(s)

1 2 3 4 > >>